Monitor M2200 Dokumentacja

Exhaust ElbowShort Elbow-P/N 4060Long Elbow- P/N 8215Air Supply Hose90° JointAir Intake Joint- P/N 4069 Flue PipeFig. 2Do not count8

SECTION DHEATER INSTALLATIONStep 1: Fill Out Owner Registration CardRemove your owner registration card from the plasticenvelope containing the owner&

FLUE PIPE CLEARANCESFlue pipe installations should provide for venting to an unconfined space through which there is a free flow ofoutdoor air. Cleara

Step 4 : Drill a Pilot HoleNOTE: The following directions apply to 'standardinstallation. For other methods, follow instructionsincluded with acc

Step 7:lnstall Flue Pipe BWall Thickness: 5-8'/? inches1. Slide the outer flange and the rubber packing ontoFlue pipe B.(Figure 11)Rubber Packing

Step 8 : Install the Spill TrayPlace the spill tray on the floor where you plan tolocate your heater.Remove the screw from the cabinet (Figure16).Posi

NOTE:The "STANDARD" damper is to be used withextension kits up to 1 bend (90° elbow) withextension kit total length of 0-73 in. or up to 2 b

SECTION EFUELINGZ?\ WARNING : Use only crystal clear kerosene (Red dyed or clear kerosene or low sulphur #1 oil). Never usegasoline, white gas, camp f

NOTE:External tank installations must comply with theNational Fire Protection Association code NFPA31 or locally applicable codes, such as theUniform

OPTIONAL CAPSULE TANK INSTALLATIONOptional capsule tank kit is available from your Monitordealer./h CAUTION: The conversion of the Monitor 2200 for us

SAFETY ALERT SYMBOLThese symbols appear as important safety precautions and should be understoodand followed by the owner to assure safe operation of

Step 4 :Remove the fuel cap. If the fuel cap is difficult tounscrew, press the valve in the center, and remove(See Figure 27).Step 6:Install the fuel

REFUELINGNOTE: When the red light marked "Empty" illuminatesand flashes, a buzzer will sound for twentyseconds. The burner mode will change

SECTION FSTARTING INSTRUCTIONSStep 1: Plug in the HeaterPlug in the AC cord, and route it away from the areaof the flue pipe. It is recommended that n

SECTION GADJUSTING ROOM TEMPERATUREPressing either the "UP" or "DOWN" button will increase When the desired room temperature is re

SECTION JPROGRAMMING THE HEATERSETTING THE DAY OF WEEK AND THE TIMEStep 1 :Set the Day of WeekPress the "SELECT" Button, at which time the &

PROGRAMMING THE WEEKLY TIMER FOR AUTOMATIC HEATER OPERATIONThe Monitor 2200 Heating System is capable of providingup to 4 different temperature settin

SECTION KPROTECTIVE FEATURESLOSS OF POWER-AUTOMATIC RESET:NOTEilf power to the heater is interrupted, a thud-likenoise may be heard in the combustion

SECTION LCARE OF THE HEATERPush operation switch to "OFF" remove the AC Plug from the wall outlet and wait approximately 30 minutes forthe h

1.Remove the capsule fuel tank, and the fuel filter from the fuel sump tank.2.Remove fuel with the siphon,remaining fuel must be sucked up with the pl

SECTION MTROUBLESHOOTING GUIDEShould symptoms appear during the operation of your heater, refer to the chart below, If you are unable to restorenormal

SECTION AIMPORTANT CAUTIONM/VARNINGUSE ONLY RED DYED OR CLEAR KEROSENE ORLOW SULPHUR #1 OIL. NEVER USE GASOLINE,WHITE GAS, or CAMP FUEL. USE OF SUCH F

Monitor 2200™ Vented Heating Systems Limited WarrantyMONITOR PRODUCTS, INC., warrants eachMONITOR 2200 vented heating system sold by it tobe free from

3. Keep heater clean and do not store any flammable items on or near theheater.4. Don't use the heater for drying clothes.5. Should anything abno

7. Do not place yourself or others too close to the heater.8. Installation of heater in extreme humidity or dust areas is notrecommended.Any removal o

11. Do not install nor exhaust the flue pipe into a crawl space or underneath floor,nor into a flue or chimney.X'///////////IX-FlueorChimney12.OP

SECTION BSPECIFICATIONSModel Monitor 2200Fuel TypeRed dyed or Clear Kerosene or Low Sulphur *1 OilHeater Efficiency93%*Heat RatingHigh:22,000 BTU/hour

SECTION CBefore installing your heater, be sure to check and comply with local and state building and electrical codesthat may apply to vented heaters

ACCESSORIES YOU MAY NEEDCheck the list below and see your MPI dealer for accessories you may need or want for installation of your heating-system.A\ C